Appliance Repair Prospect Heights

Материал из JD Edwards E1
Перейти к навигации Перейти к поиску

Remove the DC motor from the mount. Make sure you remove any electric power source that could cause it to start turning accidentally. You may need to follow the manufacturer's instructions to do this, as some motors are very much wedged into position and could pose a risk of electrocution.

Next, you can test the electric motor's continuity (or connection) by attaching it to a volt ohmmeter. Place the red and black leads in the connections of the meter (the black lead should be connected to the "common point" and the red lead Good Old Appliance Service to the "ohms"), and then ensure that the meter has been set to "ohms". Test that the meter is working properly by touching these two leads together - the screen should read zero ohms (or full continuity).

To test your DC Motor, touch the leads on the ohmmeter with the leads on the motor. The screen of the meter should show a low resistance between 10 and 30 Ohms. If it shows an infinite ohms reading or an open circuit, you should rotate the motor's end shaft. The ohmmeter should give different readings as this shaft is rotated (which is an indication that the electric motor itself is good, but that there is a problem with the electrical circuit. If the meter still reads as an open-circuit, the conducting brushes could have gone "bad".

Use a screwdriver to remove the brushes from the end of the electric motor (you can find them under the plastic end caps at the opposite end of the motor to the drive shaft). Check the brushes for cracks and breaks on the surface. The area of the brush which sits against the conductor should be smooth and curvy. The motor will not work if there are broken wires or springs. If the brushes are fine, the problem could be the commutator.

Take the screwdriver again and use it to remove the rear end cap of the DC electric motor (by removing the two screws that run the motor's length). The plates that make up the commutator should have an opening between them. If you see any burned varnish or broken wires, then the commutator is failing and will need to have its damaged parts replaced.

Overloading plug-ins causes fire hazards in your house. It gets overloaded by too many thing plugged in at once. The cords can burn and the plug itself can emit smoke and fire. You should check the fuse box if you have too many items connected to one fuse. This can cause the fuse to shut down power to certain parts of your home. When you have them check out the fuse box, get it fixed so the wires are not messed up and won't cause a fire. It can shock you if sparks are coming out of it. If it is shooting sparks, turn off the power to unplug it so you will not get hurt and so it will not cause a fire.

It can cause the plug-in to melt if it gets too hot, and it will leave black marks on the face of the plug-in. If this happens, it is not good to use it until the wires are checked out first to see if it works right and if it is OK to use or to see if the wires need to be changed because they can be burned or they could be fried. It can also fry sockets on computers, TVs, and other electronics that are overloaded. Overloading plug ins can cause the device to overheat. If this happens, unplug it before it gets hotter. Don't plug-in too many lights at once because that will overload it and blow the circuit breaker.

Extension cords are no different. Never put an overloaded extension cord on an old carpet or rug as this can also start some fires. If you smell smoke coming from the plug, pull it out of the wall because it is overheating. If an appliance shorts out while plugged in, the electricity can travel up the cables and into the socket. This will leave burn marks on both the socket and wall. If this happens, you will have to get the wires in the walls checked out and fixed because that can start a fire at any time if the wires are not replaced.

The fire damage that could be caused from it will have to be removed and cleaned. It is dangerous to remove the wires yourself. Before working on the wires, all power must be turned off. Professionals must make sure that the power is working properly when they turn it on. If it's not hooked up correctly, sparks can shoot out and shock you or start a blaze. If it starts a fire, it can spread through the wires throughout the house and fry everything.